Solar-powered security cameras are only as reliable as the battery behind them. In most off-grid and semi-off-grid installations the panel tops up the pack on good days, but it is the battery that has to carry the load through cloudy weeks, tropical rain and cooler nights. A generic "12V 7Ah" battery bought off the shelf is rarely the right answer — duty cycle, temperature and enclosure are too specific. This checklist walks through what to specify when you commission a custom pack for a solar security camera, so the quote you get reflects your real site rather than a catalogue average.
1. Start with the sun-free window, not the camera's rating
The camera's power draw is the easy number. The hard number is how many consecutive days with little or no sun the system must survive while still recording. A pack sized only for a single night will drop out in the monsoon season. Tell the factory your worst-case sun-free window (many buyers spec 3–7 days) and the average daily draw; that combination, not the camera's label, drives capacity.
2. Capacity: sizing for the worst week
Capacity is where most solar-camera packs are under-specified. Work it backwards: daily consumption × sun-free days × a safety margin, then derate for temperature. The table below shows typical starting points for common camera classes — treat them as a conversation opener, not a final spec.
| Parameter | Typical value | Notes |
|---|---|---|
| Nominal voltage | 12.8 V (LiFePO4 4S) | 6 V and 24 V builds also common — on request |
| Usable capacity | 6 / 9 / 12 Ah | Small bullet, PTZ and 4G models respectively — typical |
| Sun-free survival | 3–7 days | Depends on panel wattage and site — confirm with factory |
| Continuous discharge | 1–2 A | Camera + transmitter steady draw — typical |
| Peak discharge | 4–6 A | IR illumination / PTZ slew, short bursts — typical |
| Cycle life | 2000 cycles @ 80% DoD | LiFePO4 — typical |
| Certifications | UN38.3, MSDS | For shipping; IEC 62133 / CE on request |
3. Voltage and the discharge profile
Solar cameras draw little on average but spike when the IR array, spotlight or PTZ motor engages. A continuous rating of 1–2 A with a 4–6 A peak for a few seconds is typical. The pack and its BMS must be rated for the peak, not just the average, or you will see voltage sag and unexpected shutdowns at night. State both figures to the factory.
4. Enclosure, ingress protection and temperature
The pack often lives inside the camera housing or a sealed junction box exposed to the elements. Ask for an enclosure rated to your site — IP65 is a common starting point for outdoor units. Equally important is the charge-temperature window: a LiFePO4 pack that charges below freezing will be damaged by the solar trickle. A BMS with low-temperature charge cut-off is the single feature that prevents winter failures.
5. Chemistry: LiFePO4 vs Li-ion for solar duty
For a pack that sits partially charged and cycles daily in heat, LiFePO4 is usually the better choice — it tolerates high states of charge, runs cooler and lasts far longer than standard Li-ion. Where size and weight dominate (a small bullet camera), a Li-ion or Li-po cell may win on volume. We only build with original-pack Grade A cells — never B-grade, never C-grade, ever. Tell us which trade-off matters for your product and we will propose the chemistry to match.
6. The BMS features that actually matter here
Skip the marketing spec sheet and ask for four things: low-temperature charge cut-off (see above), cell balancing so the pack ages evenly, a fuel gauge / communication output if your camera reports battery level, and over-discharge protection set above the camera's brownout point. These are the differences between a pack that lasts two years and one that fails in the first wet season.
7. Certifications and shipping for importers
If you import, the battery travels as regulated cargo. UN38.3 test summary and an MSDS are the baseline for both air and sea freight; some markets also expect IEC 62133 or CE on the product. List your destination and intended shipping mode up front so the factory issues the right documents with the shipment rather than after a hold at customs. We can supply UN38.3 and MSDS; product-level certifications are confirmed per order — on request.
Send this brief and get a priced proposal
Give us the camera model, panel wattage and your worst-case sun-free window — even a photo of the current pack is enough to start — and we reply within 24 hours with a specification proposal and pricing tiers. Samples are charged and credited to your first production order.
Quick Inquiry
Not every number above will be fixed when you first inquire — and that is fine. Send the camera model, the panel wattage and your worst-case sun-free window, and a good factory will close the gaps from there. The point of the checklist is to start the conversation with the facts you have, so the pack you receive is built for your site, not a generic shelf unit.
Related
Browse the product lines we build — each links to its own page:
